Bazar hudební nástroje Hudební nástroje

Hudební fórum

Diskuze o všem, co souvisí s hudbou a hudebními nástroji.
 

Seřízení rezofonické kytary

Klasické, jumbo, westernové, ...

Seřízení rezofonické kytary

Příspěvekod Irudziu » 4.08.2010 20:28

Rezofonická kytara Oscar Schmidt by Washburn: Pořídil jsem si tohle "Dobro" ze zvědavosti a musím říct - za ty peníze (asi 7k) fakt radost. Jen zvuk je hodně kytarový a tak mě napadlo jestli ten šroub nad kobylkou směrem do rezonátoru není na modifikaci zvuku. Nevíte to, prosím, někdo? Díky :shock:
Irudziu
 
Příspěvky: 1
Registrován: 4.08.2010 20:17

Re: Seřízení rezofonické kytary

Příspěvekod ...EDGE... » 4.08.2010 20:47

Modifikaci zvuku? Kytarovy zvuk? Zkus s nim zakroutit co se stane ne?
Uživatelský avatar
...EDGE...
 
Příspěvky: 2562
Registrován: 4.08.2008 19:04
Věk: 20
Bydliště: Praha Prahoucí

Re: Seřízení rezofonické kytary

Příspěvekod golf33 » 5.08.2010 0:03

No, já bych kroutil opatrně, aby něco neupadlo. A pro jistotu bych počítal závity, ať to můžu dát do původní polohy :D :D :D
T.Burton Rambler Dreadnaught/Cut
Furch D 22 SR 12str.
Furch D 24 SR 6str.

http://www.youtube.com/watch?v=qBnB4H_zJ6U
golf33
 
Příspěvky: 49
Registrován: 22.07.2010 0:07
Bydliště: Kousek od Ostravy

Re: Seřízení rezofonické kytary

Příspěvekod Tonda » 5.08.2010 20:14

Já sice nemám dobro, ale normální rezonátor (=plechovej) a tam takovej šroub (spider tension screw) není,

...ale tady jsem ti vygůglil jak se to má správně nastavovat:


"It's now time to adjust the spider tension screw. Tune the guitar to pitch and play an open string. The note should have a distorted “fuzz tone" sound. If not, loosen the tension screw until you hear this effect. If you loosen the tension screw and cannot get this distorted sound, the break angle from the saddles down to the tailpiece may be too sharp (this can damage the cone and hamper tone and volume). In this case, the tailpiece may have to be bent upwards slightly to achieve the proper break angle. Bend the tailpiece up in small increments and play a string until you hear the “fuzz tone" effect. (Loosen the strings temporarily while bending the tailpiece up.)

Now that you've got the “fuzz tone,” tighten the tension screw 1/4-turn and play the string again. Repeat this process until the fuzz sound is gone, then go 1/2-turn more. This should give you good tone and volume, while avoiding damage to the cone
. "

http://www.stewmac.com/freeinfo/a-spidersetup.html
"I took a long, hard look at my current inventory and realized I had enough guitars and gear to supply three garage bands..." (kdosi na FenderForum.com :))
Uživatelský avatar
Tonda
 
Příspěvky: 1163
Registrován: 13.08.2007 18:10


Zpět na Akustické kytary

Kdo je online

Uživatelé procházející toto fórum: Žádní registrovaní uživatelé a 1 návštěvník

TOPlist